how to sweat copper pipe to a shower valve

Re: How to "un sweat" 1/2" copper from shower valve; Author: hj (AZ) Drain the water from the pipe and valve. Take the valve apart. Heat the connection. Pull the copper out of the joint. Reclean and reflux both parts of the connection. Heat the connection and push the copper tube back in. Resolder the joint.

Detailed info on how to sweat copper lines and cutoff valves. There is a second video coming that is a different point of view on the sweating. Subscribe t...

flipping slumlord. Joined Jan 6, 2009. ·. 5,116 Posts. #2 · May 13, 2012. Ed911 said: There is a warning on the valve that says, caution, excessive heat will melt plastic internal parts... I was told to disassemble the valve and sweat the up-pipe and tub plug in place, and then reassemble the mixing valve...

The big things about sweating joints is to make sure that you clean both the (inside of the) fitting and (outside of) the pipe really well, use flux, heat the joint not the solder until when you put the solder onto the joint, it essentially just sucks itself into the joint, and then don't let it move until it resolidifies.

Because I build showers, I must also know how to do plumbing..in this video I show how to sweat in a shower fixture.

Part (2). Tile Master Atlanta presenting how to replace, install shower or bathtub rough in Valve ! STEP BY STEP! How to solder copper pipes, preparation an...

Kung Fu Maintenance demonstrates soldering copper pipe into brass valve plumbing fittings. No candy coating here ~ it is not always easy.Hire A Handy Man ...

How to Solder a Moen Shower Faucet Valve You can find any of the items seen in this video below and your purchase will help support this channel. Thank You...

No torch...no solder...This is a video on how to join copper pipe with out soldering using different types of fittings that are on the market today.....Pleas...

Re: How to "un sweat" 1/2" copper from shower valve. Author: hj (AZ) Drain the water from the pipe and valve. Take the valve apart. Heat the connection. Pull the copper out of the joint. Reclean and reflux both parts of the connection. Heat the connection and push the copper tube back in. Resolder the joint.

Re: Connecting Copper Pipe to New Shower Valve. Author: Dunbar (KY) Sweat connection is by far the more permanent and solid connection to the valve. - - - - - -. Always be aware of cross-connections in your potable water systems---They could one day harm you and your loved ones. Post Reply.

New York. Soldering a Shower Valve In. 1. I'm going to use 2 female threaded adaptors for the hot and cold inlets that will connect to 1/2 copper a few inches long on each side that will connect to 90 degree elbows, and then another 2 sections of pipe going into couplers which will connect to the existing hot and cold pipes.

For DIYers eager to take on plumbing tasks, one of the most important skills to master is how to sweat copper pipe—a process commonly referred to as soldering—in order to achieve leak-proof ...

I sweated 3/4 copper to 3 full port ball valves, brass bodies. I used a full propane torch, max flame length, spread lots of flux onto both valve and pipe after a very thorough scrub with steel wool, and was surprised how long it took to warm up enough to melt solder.

Sweating a pipe is a slang term for soldering a pipe or joint for the purpose of sealing a new joint or mending a fault. This is a basic plumbing process frequently used in improvement projects. Sweating a pipe and connector involves proper preparation of the surface, heating the cut end of a copper pipe and the connecting piece, which will ...

For example, this Delta rough-in valve allows the use of either 1/2" NPT threaded connections or soldered 1/2" OD copper on the same valve. I'm suggesting removing one or all of the threaded connections and just sweating the copper directly to the valve, thus eliminating the threads from ever leaking (since you're not using them.)

Once you determine the location of the shower valve, tub spout, and shower head you’ll need to cut the pipes to size. Autocut tools are great for this because they’re quick and painless. Cut all the copper to size, clean the edges with emery cloth or a brush, and debur the pipe with a deburring tool.

Illinois. Assuming the pipe is copper, then the choices are a sweat or a compression. A threaded won't be used (unless you sweat on a threaded fitting to the pipe). Compression fittings are easiest to install, but easy to replace if a valve goes bad. Since your using a ball valve it is more reliable, so it may not need replacement.

2. Cut into an existing supply pipe with a pipe cutter. Put a bucket under it to catch water that will flow out once you've made the cut. Open any other faucets or valves connected to the pipe and ...